health and safety video
processes to disassemble
-
Download 2017-03-09 18-28-38.pdf
2017-03-09 18-28-38.pdf Details
Thursday, 09 March 2017 [358.3KB] -
Download 2017-03-09 18-27-23.pdf
2017-03-09 18-27-23.pdf Details
Thursday, 09 March 2017 [442.9KB]
lock out tag out- permits
-
Download 2017-03-09 18-31-44.pdf
2017-03-09 18-31-44.pdf Details
Thursday, 09 March 2017 [694.5KB] -
Download 2017-03-09 18-32-38.pdf
2017-03-09 18-32-38.pdf Details
Thursday, 09 March 2017 [616.6KB] -
Download 2017-03-09 18-33-23.pdf
2017-03-09 18-33-23.pdf Details
Thursday, 09 March 2017 [595.2KB] -
Download finished permit to work form.pdf
finished permit to work form.pdf Details
Saturday, 11 March 2017 [561KB] -
Download finished service form.pdf.1
finished service form.pdf.1 Details
Saturday, 11 March 2017 [640.8KB]
Day 1 review
6/3/17
today we started to learn how the pump worked and all the basics behind it we looked at a fully disassembled pump on the table in the class room. we also looked into the manufacturing and technology board in the workshop that covered all the hazards in the work shop. we looked into the basics of lock out tag out (L.O.TO) and got told about how it all works in a real world situation. also looked at the logistics of having 2 pumps on a plant instead of 1 for break down purposes. overall i was happy with how the day way carried out and learnt a lot of new information
.
Day 2 review
7/03/17
today we went back over lock out tag out and i had a full understanding of how the whole system worked, once the tutor had put it into a real life situation i could fully understand why it is so import not just for your safety but for others. we wrote out our step by step guide so we knew what we would have to check and go through once we go out into the workshop, we then headed out into the workshop to complete a L.O.T.O with the permits. we also viewed a complete slide show on how to fully disassemble the pump so when we came back on Thursday we had a understand of how it will be done. we also looked into all the different coupling (eg jaw coupling) different types of seals (eg o'ring seal, rope seal) safety shields and the reasoning behind them. overall i was happy with how the day was carried out, only let down would have to be the other groups talking loudly making it hard to follow what the tutor was saying.
Day 3 review
9/03/17
today we went over s.c.r.u.m and the reasoning behind using it, we used post-it notes on a piece of paper under headings so we knew what was compete, what needed to be completed and what hasn't been started, i could see how useful this would be if another shift started on the project that i was completing. we managed to completely pull the pump apart but it was a very close call and used up most of the spare time we had left in the school day. it was good to have a bit of hands on work after all that time spend in the classroom.
Day 4 review
10/3/17
today we changed shifts on the pump and instead of pulling the pump apart we changed to reassembling the motor, well the other group started work on reassembling the pump. needed "replacing" was the o'ring, bearing and mechanical seal. the o'ring and mechanical seal were missing completely and the bearings fall under preventative maintenance as it would only cost $5 each for the two new bearings. I worked a total of 26 hours at a rate of 40/hr so I'm owed $1,040 before tax. the instructional video the other group left for us to rebuild the motor was very well carried out, making it easy to reassemble, i was disappointed to not have anything to hand over to the other group as a team member was asked to make one but was unable to carry it out for some odd reason, I will now know he is an unable member and not rely on him for any thrower tasks. I was happy with how fast Kade and I were able to reassemble the motor and carry out all the tasks required. we also finished the procedure of L.O.T.O and got everything signed off with ease apart from a team member that left, so the pump is still locked off at this point.
time sheet
-
Download wintec 1.pdf
wintec 1.pdf Details
Saturday, 11 March 2017 [568.5KB]
health and safety
-
Download 2017-03-09 18-34-52.pdf
2017-03-09 18-34-52.pdf Details
Thursday, 09 March 2017 [483.7KB] -
Download 2017-03-09 18-34-04.pdf
2017-03-09 18-34-04.pdf Details
Thursday, 09 March 2017 [492.5KB] -
Download 2017-03-09 18-35-41.pdf
2017-03-09 18-35-41.pdf Details
Thursday, 09 March 2017 [502.6KB] -
Download 2017-03-09 18-30-50.pdf
2017-03-09 18-30-50.pdf Details
Thursday, 09 March 2017 [631.8KB]
Feedback
Basil Swart
12 March 2017, 20:09
Basil Swart
06 April 2017, 9:21
Awesome review and input, Industrial Plant Simulation is now signed as Complete.
Hi Hunter (got it right this time) - really strong, accurate and technically correct review. You and Cade worked well as a team and yes, unfortunately the "other" team member did drop you guys right in it. This is being discussed at a "higher" level. You have overcome a hurdle and shown great maturity and forethought in this particular part of the course. I do like the way you submitted the documents in pdf format.